Order By Phone 1.855.533.4685 - Mon-Fri 10:30am to 5:00pm

24V iP68 10 to 20m RF Single Color 5050 300 LED Strip Kit with Outdoor Driver

CODE: IP68SC24V1020

$181.06

In stock

24V iP68 Single Color LED Strip Kit with Outdoor Driver (10 to 20m)

LED Montreal has what you need to build your ultimate outdoor LED strip setup! The 10 to 20m 24V iP68 Single Color LED Strip Kit with Outdoor Driver now allows you to make longer lengths of high output 5050 LED Strips. You can build circuits of up to 20 meters without losing brightness. Combine numerous kits to our Multi Zone system, build several kits and sync them together as if it was one kit ! 

Using the appropriate Outdoor driver, you can hardwire your strip kit to your 120V power source and install it all outside. The included output wire is 14 gauge, allowing you to use a longer extention between your driver and your controller / LED Strip (up to 20 meters with 14 gauge wire). With its robust cover and waterproof connections and cables, it is your best option to power any iP68 LED Strip kit that you want to place on your patio, poolside, gazebo, rv, trailer, boat, cottage or anything outside! 

The entry level kit comes with no controller (dimmer), and includes the power supply and LED Strips. Using the drop down menu, you can easily upgrade your kit to use the RF Single Color Multi Zone Controller and Remote. To sufficiently protect your controller, we suggest using a Weatherproof Project Box.

The drop down menus also allow you to pick your prefered length and the shade of white of LED strip to perfectly match your needs! Warm White (3000K), Natural White (4500K) and Cool White (6000K). This kit only uses our ultra bright (5050) LED Chips boasting an impressive output of up to 900 Lumens per meter. Each Strip features 60 LED per meter for a total of 300 LEDs per 5 meters. To perfectly fit your needs, the Strips can be cut at every 6 LEDs (10 cm).


Unsure of your Single Color LED Strip Selection?

Visit the Single Color LED Strip Buyer's Guide page for the basics of what you need to know about Single Color LED Strips to help you choose the correct LED Strip for your application.


About our Outdoor driver: This power supply is rated iP65 or better, which means it is waterproof and safe to put outside. Keep in mind that the connections are not waterproof and need to be protected. The 24V power supplies provide constant 24V current and feature two distinct ports for input and output: the 120V AC input has 3 wire connections: one for the live wire, one for the neutral wire and one for the ground. The 24V DC output features 2 connections: one positive and one negative, provided with 14 gauge wire. We will provide you with the appropriate 24V power supply to provide enough power for the kit you chose.

Compliant with worldwide safety regulations for lighting, the Outdoor hard wired power supply has been the electrician’s choice for several years! 

This single output power supply has integrated protection from short circuits, over current and over voltage as well as over temperature. All circuitry of Outdoor power supply is concealed inside a fully isolated plastic case that is cooled by free air convection. 

Important: Outdoor power supplies are not compatible with AC dimmers. To dim your LEDs with these power supplies, you require the Multi Zone controller.

About the iP68 Strips: Note that only the LED Strip is water proof, the connectors at both ends of the strip are not waterproof and must not be in contact with water or moisture. You can use extra silicon and heat shrink tube to make your setup safer. 

The iP68 strips are not self adhesive, to maintain them in place we suggest using GE pure silicone and double-sided adhesive tape. Simply put the silicone on the back of the strip, then put the double-sided tape on top of the silicone. Once the silicone is dry, your strip is ready to install! Additional option when looking for a sharp and subtle way to hold your ip68 LED strips, the Silicone Mounting Brackets for LED Strips from LED Montreal are a great solution.

If you are looking to install iP68 submersible LED strips to your awning, pool, deck, RV, boat, docks, or anything of that nature, we invite you to read our page on how to install your under awning LED strips.

For every 15m-20m kit, your package will include a Y shape splitter, which you need in order to split your circuit as evenly as possible. On longer circuits like these, the light might tend to get dim on the ends if power isn't distributed evenly.

IMPORTANT NOTE: Since the Outdoor Driver has to be hardwired into the wall dimmer using 110-120V power, it requires to be installed by a qualified professional.
 

Dimensions: 5 meter long, 1.2cm wide and 0.5cm thick

Waterproof (IP68)
Suitable for indoor and outdoor usage
5 meter strip, 60 LEDs per meter, 300 LEDs in total
Can be cut every 6 LED (20 cm)
LED type: 5050 SMD
Luminous intensity:850 lm/m
Required Power: 9.6W /m at 24V

 

No FAQ found, submit a question!

Loading...