Order By Phone 1.855.533.4685 - Mon-Fri 10:30am to 5:00pm

12V iP68 Multi Zone RF RGB LED Strip kit

CODE: IP68RFMZONEKIT

$90.91

In stock

iP68 Submersible Multi Zone RF RGB LED Strip kit

The basic kit comes with 1 x 5m Submersible ip68 150 LED RGB Strip + 1 Multi Zone RGB remote + 1 Multi Zone controller+ 1 power supply. Multiple Strips are displayed to show some of the colors that the actual Strip can achieve and to illustrate that you can control several units with one remote. You can customize your kit using the drop down menus above.

The latest LED control technology is here and you can now use it to operate all your exterior LED strip lighting using a single RF remote! Want to use submersible ip68 LED strips to illuminate your camper, R.V., pool, deck, cottage, docks, boat or any outdoor area of the sort? The Multi Zone RF Submersible ip68 RGB LED Strips kit from LED Montreal is just what you need! It allows you to sync an unlimited amount of those Submersible ip68 RGB LED Strips in each of the four available zones. Plus, it works in extremely simple and effective fashion!

Your remote is your best friend.
This kit comes with a Multi Zone RF remote which operates on 2.4 GHz frequency, giving it with a range of up to 30 meters and features numerous functions. The center touchpad gives you the possibility of choosing directly a lighting color (press and hold the ON (│) button of the Zone to get the color White) while another small touchpad gives you control over the brightness of the lighting. You can also select among 9 different automatic light changing modes and even control the speed of the changes! Please note that we strongly suggest investing in a second remote to be used as a backup in case you lose the first one... you don’t want your whole setup stuck on blinking red mode because your dog ate the remote!

About the Submersible ip68 LED Strips.
For any outdoor use, we highly recommend using one of the Submersible ip68 LED Strips. Mixing the energy and money saving features of the LED strips with the water protection required for this type of setup, they are the best option for your exterior lighting needs. They’re especially great for your camper, R.V., house, cottage, boat or any similar outdoor use. Unlike the regular ip65 LED Strips that are waterproof on 3 sides, the Submersible ip68 LED Strips are encased in a thick clear tube filled with silicon so they are completely waterproof.  Please note only the Strip is waterproof. The connectors on each end of the Strip, the controller as well as the remote must not come in contact with humidity or liquids since they are not waterproof, so please make sure that you properly protect these parts from humidity.

The iP68 strips are not self adhesive, to maintain them in place we suggest using GE pure silicone and double-sided adhesive tape. Simply put the silicone on the back of the strip, then put the double-sided tape on top of the silicone. Once the silicone is dry, your strip is ready to install! Additional option when looking for a sharp and subtle way to hold your ip68 LED strips, the Silicone Mounting Brackets for LED Strips from LED Montreal are a great solution.

The 4 Zone set up is the coolest thing ever!
A few examples:

•  Control the lighting around your pool on Zone 1, your deck on Zone 2, your awning on Zone 3 and your garden on Zone 4.

•  Divide your boat lighting in two zones and control one section with Zone 1 and another section of the same area using Zone 2.

•  Alternatively, you could set up the whole area on a single zone and have all your strips change color in sync... that’s how powerful and versatile this kit is!


Adding on to a Zone is easy!

For a new product or a product that has never been linked before:

  1. Disconnect the power supply from the controller.
  2. Turn the light back on and within 3 seconds; press the ON (│) button of the zone you want to assign (1 to 4) on the remote control.
  3. The light will slowly flash 3 times to indicate that it was successfully linked.


Change a light from one zone to another.

If the light you want to add to a zone was previously assigned to a different one, you will first need to unlink that light.

  1. Identify which zone the light is currently assigned to.
  2. Turn off the light(s) you want to program.
  3. Power the light back on and within 3 seconds; press the ON button of the previously assigned zone 5 times quickly.
  4. You can then proceed and program your light according to the add-on procedure outlined above.

For extensive instructions on how to install your Multi-Zone setup, VISIT THIS PAGE.

Your power sources.
Please note that although you can sync and control an unlimited amount of LED Strips in each Zone, make sure that you have a power outlet available for each 20 meters of 150 LED RGB Strip within the same zone.  For example, if you wish to light up your favorite area with 30 meters of ip68 150 RGB LED Strip, your kit should connect as follow:

Circuit 1: 1-10A Power supply, 1- T shape connector, 1- RF Controller, 4- 5m spools of ip68 150 RGB LED Strips
Circuit 2: 1- 6A Power supply, 1- RF Controller, 2- 5m spools of ip68 150 RGB LED Strips

Configuration for 20 meters of ip68 RGB 150 LED Strip:
The Multi Zone kit for 20m of ip68 RGB 150 strip (the maximum length of RGB 150 strip possible for 1 circuit) comes with a T shape splitter. You can connect 2 strips (10m) on the left output and 2 strips (10m) on the right output. You can't connect 3 or 4 strips one after the other on the same output, the tension on the circuit will be too high and you will damage your strips.

Configuration for 15 meters ip68 RGB 150 LED Strip:
The Multi Zone kit for 15m of ip68 RGB 150 strip comes with a T shape splitter. You have to connect 2 strips (10m) on one side and 1 strip (5m) on the other. You can't connect 3 or 4 strips one after the other on the same output, the tension on the circuit will be too high and you will damage your strips.

Configuration for 10 meters of ip68 RGB 300 LED Strip:
The Multi Zone kit for 10m of RGB ip68 300 strip comes with a T shape splitter. You have to connect 1 strip (5m) on one side and 1 strip (5m) on the other. You can't connect more than one strip of RGB 300 on the same output, the tension on the circuit will be too high and you will damage your strips. Note that for 10m of ip68 RGB 150 strip, it is preferable to split the circuit in the middle and have one strip on each side.


As always, our team of experts is available should you have any questions or require assistance putting your project together.

 



No FAQ found, submit a question!

Loading...