Got a question? Ask Mike!
Mike
.
Categories

15m to 20m Multi Zone iP65+ 24V RGB+White Strip kit

MZRGBW15
$374.95
In stock
MZRGBW15
+
Add to wish list
Delivery
Shipping time and rates:
Payment options
Our advantages
Find similar

15m to 20m Multi Zone iP65+ 24V RGB+White Strip kit

The base kit includes 3 or 4 x 5m UL listed RGB+W Strip (300 LED), 1x 24V 240W Hard Wired power Supply and 1x RGB+White Multi Zone Controller. You have the possibility of adding a remote control or a Wi-Fi controller kit by using the pull down menu above.

Standard RGB Strips are appreciated because of their wide variety of colors but do tend to cause a slight problem when the time comes to reproducing white. Since the Standard RGB Strip uses a mix or Red, Blue and Green to makes colors, its version of the color white tends to be very blue or even purple.   

The RGB + White Strip kit from LED Montreal will output the full RGB Spectrum PLUS a true White and features a certified, UL Listed Strip. This chromatic prowess is achieved with special 5050 Chips that integrate 4 separate lights: Red, Green, Blue and White. Each Strip features 300 Chips over a span of 5 meters, or if you prefer, 60 LEDs per meters, giving this Strip an amazing brightness, no matter what color you select. Note that the RGB+W Strip will only produce one shade of White, either it be warm white, natural white or cool white. You will be able to select the white you prefer in the pull down menu when placing your order. Your Strip will produce one color at a time. Therefore, you cannot produce a white and a color at the same time.

The Multi Zone RGB+White kit can be matched on the same remote as other Multi Zone kits and Bulbs. Simply add it to your set up as you would with any other Multi Zone item: set it on its own zone and you are ready to go. As always, make sure that it’s connected to its own power supply and controller, as the controller has a 5 wire output and the power supply has a 24V output.

Setting up your kit is easy: have a qualified professional hook up your hard wired power supply to a 120V source then connect the 24V output wires in the screw in connectors of the controller. Then connect your Strips in the controller as shown in the illustration below, you can connect a maximum of 2 strips in series. If you plan on getting a kit of 20 meters, you will be provided with a T shape Splitter in order to connect your two series in parallel. See our FAQ to learn how to program your remote control. 

Note that the RGB+White is offered in 24V (opposite most Strips that will run on 12V), and that allows you to make a circuit of up to 20 meters parallel. Given that this product runs on 24V, you cannot use a 12V power supply for this Strip or use the provided power supply to try and power up a 12V product. Furthermore, you will notice that this Strip is 14mm wide, therefore wider than the Standard 10mm 5050 Strip. As well, Given that this Strip offers 4 colors, it features 5 connectors unlike the Standard RGB Strip that normally features 4 connectors. This being said, solder less connectors are yet to be made available for this product. Should you require to cut and reconnect your RGB+White Strip, it can be cut every 6 LED et we suggest soldering wires directly on your Strip.

Like all hard wired products, the 120V power supply should be installed by a qualified professional. 

iP65+ LED Strip with 3M adhesive
For indoor use only 5M roll, 60LED/m. 300 LED total
Certification: UL for Canada and USA
Can be cut: Every 6 LED (10 cm)
Width: 14mm, height 4.5mm 
Required Power: 9.6W/m at 24V
Recommended Power: 12W/m at 24V
LED Type: 5050 SMD
Luminus flux on white: 400 lm/m
Dimmable: yes through remote control

 

Télécommande et/ou Contrôleur RF Multi Zone pour Rubans LED RGB+Blanc

Professional grade products

Canadian and American Certifications

Quantity discounts available

Create an online quote for your project