Order By Phone
1-855-533-4685  -  Mon-Fri 10:30am to 5:00pm

Banner client project

FUT007 RF Multi Zone Remote and-or FUT036 Controller - Single Color



In stock

FUT007 RF Multi Zone Remote and-or FUT036 Controller - Single Color

This is it! This is the newest technology to control your whole lighting universe. With the RF Multi Zone Remote and-or Controller for Single Color LED Strips from LED Montreal, you can operate every single color RF LED Strip in your house. You already have a setup at home but find it quite complex and uneasy to handle? There’s your chance to improve and make it a multi zone system.  All you have to do is change the controllers for your LED strips and you can now control them all with the Multi Zone Remote. On the flipside, If you’re a newbie to all of this, you can start shaping your dream house with a RF Multi Zone Single Color LED Strips kit which includes the remote, controller and as many strips as you need. Add as many controllers as you want and assign them all to one of the 4 available zones.

The Multi Zone RF remote operates on 2.4 GHz frequency, giving it a range of at least 20 meters and the RF signal doesn’t require you to point at the controller. The center touchpad gives you control over the brightness of your lighting (up-down). You can also assign an unlimited amount of single color strips to whichever one of the 4 available zones. 

You can control the following items with your multi zone remote and controller: 3528 single color LED strips and 5050 single color LED Strips. Those items can be synced and controlled together, within the same zone. So if you set 2 x 20 meter bundles on Zone 1, for example, and then turn zone 1 on with the remote, all your LED Strips will turn on.

This controller will work with both 12V and 24V Strips and Power Supplies.

Remote Control: FUT007
Voltage: 3V (2 AAA batteries)
Transmission Frequency: 2.4 GHz
Control Distance: 30m
Dimensions: 110mm x 53mm x 21.5mm

Controller: FUT036
Dimensions: 85mmx45mmx22.5mm
Working Voltage: 12-24V DC
Maximum Output: 6A/ Channel  10A Total
Control Range: up to 30m

The 4 Zone set up is just awesome and so convenient!
A few examples:

  • Control the lighting in your kitchen on Zone 1, your bedroom on Zone 2, your living room on Zone 3 and your recreation room on Zone 4.
  • Divide a room in two zones and control one side with Zone 1 and the other side using Zone 2.
  • Alternatively, you could set up the whole house on a single zone and have all your strips turn on and off in sync... that’s how powerful and versatile this kit is!
  • You could also cut a LED strip in 2, plug in a different controller for each part and control the 2 pieces separately on 2 different zones. Note that if you do so, you’ll need an extra Quick DC Connector and power supply.

Adding on to a Zone is easy!
For a new product or a product that has never been linked before:

  1. Disconnect the power supply from the controller to switch off the light(s) you want to program.
  2. Turn the light back on and within 3 seconds; press the ON (│) button of the zone you want to assign (1 to 4) on the remote control.
  3. The light will slowly flash 3 times to indicate that it was successfully linked.

ou can repeat this procedure for each light product you want to add to your Zone.

Change a light from one zone to another.
If the light you want to add to a zone was previously assigned to a different one, you will first need to unlink that light.

  1. Identify which zone the light is currently assigned to.
  2. Disconnect the power supply to turn off the light(s) you want to program. 
  3. Power the light back on and within 3 seconds; press the ON button of the previously assigned zone 5 times quickly. 
  4. You can then proceed and program your light according to the add-on procedure outlined above.

For extensive instructions on how to install your Multi-Zone setup, VISIT THIS PAGE.

As always, our team of experts is available should you have any question or require assistance putting your project together.