24V iP20 RGB+White LED Strip Kit 5m - 96 LEDs/m

24V iP20 RGB+White LED Strip Kit 5m - 96 LEDs/m

The base kit includes a 5m cULus listed RGB+W Strip (96 LEDs per meter), a 24V 96W Power Supply, an RGB+White E3-RF Multi Zone Controller and a FUT096 remote. You have the option to choose a different remote in the dropdown menu.

Standard RGB Strips are appreciated because of their wide variety of colors but do tend to cause a slight problem when the time comes to reproducing white. Since the Standard RGB Strip uses a mix or Red, Blue and Green to makes colors, its version of the color white tends to be very blue or even purple.  

The UL Listed RGB + White Strip kit from LED Montreal will output the full RGB Spectrum PLUS a true White. This chromatic prowess is achieved with special 5050 Chips that integrate 4 separate lights: Red, Green, Blue and White. Each Strip features 300 Chips over a span of 5 meters, or if you prefer, 60 LEDs per meters, giving this Strip an amazing brightness, no matter what color you select. Note that the RGB+W Strip will only produce one shade of White, either it be warm white, natural white or cool white. You will be able to select the white you prefer when placing your order. With the FUT096 and B3 remote control, your Strip will produce only one color at a time, so it is not possible to mix white with another color. However, you can produce pastel shades (Colors + White) with the FUT092, C5 and Y3 remote controls.

The Multi Zone RGB+White kit can be matched on the same remote as other Multi Zone kits. Simply add it to your set up as you would with any other Multi Zone item: set it on its own zone and you are ready to go. As always, make sure that it’s connected to its own power supply and controller, as the controller has a 5 wire output and the power supply has a 24V output.

Note that the RGB+White is offered in 24V. Given that this product runs on 24V, you cannot use a 12V power supply for this Strip or use the provided power supply to try and power up a 12V product. Furthermore, you will notice that this Strip is 12mm wide, therefore wider than the Standard 10mm RGB 5050 Strip. As well, given that this Strip offers 4 colors, it features 5 connectors unlike the Standard RGB Strip that normally features 4 connectors. This being said, solder less connectors are not available available for this product. Should you require to cut and reconnect your RGB+White Strip, it can be cut every 6 LED et we suggest soldering wires directly on your Strip.

To set up the output mode:

Press the "SET" button continuously to switch the output mode to the Green Light (RGB+W). The controller will log out if there's no operation within 3 seconds. Output modes are indicated by the color of the indicator light.

Red Light: RGB Strip (Not compatible with the strip included in this kit.)
Green Light: RGB+W Strip
Blue Light: RGB+CCT Strip (Not compatible with the strip included in this kit.)

Linking Code Instructions:

1. Connect your LED strip and transformer to the controller. Make sure the Strip turns on, then briefly press the SET button on the controller.
2. Briefly press the " | " button on the remote control 3 times within 3 seconds.
3. The lights will flash slowly 3 times to indicate a successful connection.
4. If the connection fails, repeat the steps.

Unlinking Code Instructions:

1. Turn off for 10 seconds by unplugging the transformer, then plug it back in.
2. Briefly press the " | " button on the remote control 5 times within 3 seconds.
3. The lights will flash rapidly 10 times to indicate a successful disconnection.
4. If the disconnection fails, repeat the steps.

Attention:

Turn off the power supply before installation.
Ensure the input voltage matches the device requirements.
Avoid using the device in areas with large metal surfaces or strong electromagnetic waves, as this may affect the remote distance.

LED Strip Specifications:

Brand: CDNLUX
Model: MTL-FP12AGIDJ-96ARGBW
Certification: cULus for Canada and USA E498952

Chip: Epistar 5050 RGBW SMD 4 in 1
Chip density: 96 LEDs per meter
Can be cut: All 6 LEDs (62mm)
Length: 5 meters
Width: 12mm
Height: 2mm

Voltage: 24V DC
Power consumption: 15.4W/m
Recommended power supply: 19.2W/m, Class 2 power supply required
Recommended power supply for 5m: 96W, Class 2 power supply required
Typical luminous flux on white: 640 Lumens/m (will slightly vary depending on Kelvin degrees chosen)
Available colors: RGB + White (3000K, 4000K or 5000K)
CRI: 80+
Lighting angle: 120°
Lifespan: 50 000 Hours

Self-adhesive: 3M
iP rating: iP20
Suitable environment: For indoor use only
Operating temperature: 40C to -10C
Connections included: 5 wires (17cm) on one end and 5 wires (17cm) on the other end
Dimmable: Yes, with a low voltage dimmer/remote combo
Heat dissipation: Must be installed on a heat dissipating surface or in appropriate aluminum channel

 Spec Sheet (PDF)

E3-RF Controller Specification:

Model No.: E3-RF
Input Voltage: DC12~24V
Output: 6A/Channel
Total Output: Max 12A (4A at 24V or 5A at 12V to comply with Class 2 requirements)
RF: 2.4GHz
Control Distance: 30m
iP Rating: iP20
Working Temperature: -10~40°C
Output Connection: Common anode
Dimensions:100.6mm x 40mm x 17.6mm

E3-RF Instruction Guide (PDF)

FUT096 Remote Specification:

Model: FUT096
Voltage: 3V (2 x AAA batteries)  
Transmission Frequency : 2.4GH
Control Distance: 30m
Dimensions: 120mm x 52.5mm x 21mm