Order By Phone 1.855.533.4685 - Mon-Fri 10:30am to 5:00pm
Closed for Easter on April 19, 20, 21 & 22 

24V 5m iP20 RGB+W 5050 LED Strip - 60LEDs/m (Strip Only)



In stock
Quantity  10+   40+ 
Price per unit  $79.95   $74.95 

24V 5m iP20 RGB+W 5050 LED Strip - 60 LEDs/m (Strip Only)

Standard RGB Strips are appreciated because of their wide variety of colors but do tend to cause a slight problem when the time comes to reproducing white. Since the Standard RGB Strip uses a mix or Red, Blue and Green to makes colors, its version of the color white tends to be very blue or even purple. 

The cUL Certified RGB + White Strip kit from LED Montreal will output the full RGB Spectrum PLUS a true White. This chromatic prowess is achieved with special 5050 Chips that integrate 4 separate lights: Red, Green, Blue and White. Each Strip features 300 Chips over a span of 5 meters, or if you prefer, 60 LEDs per meters, giving this Strip an amazing brightness, no matter what color you select. Note that the RGB+W Strip will only produce one shade of White, either it be warm white, natural white or cool white. You will be able to select the white you prefer in the pull down menu when placing your order.

When used with the Multi Zone system, your Strip will produce one color at a time. Therefore, you cannot obtaine a white and a color at the same time. This limits the Strip's consumption to 10W/m. We then recommend using 12W/m on your power supply.

When used with the Advanced Multi Channel system, you will be able to mix the white and the colors in order to obtain a more pastel shade. At that point, we recommend using 18W per meter for your power supply.

This iP20 LED Strip does not offer any water protection. iP20 strips are ideal for indoor usage in aluminium profiles. Moreover, no connectors are available for this type of strip. For outdoor applications where the strip will be directly exposed to the elements, we recommend iP67+ grade strips.

Note that the RGB+White Strip is offered in 24V (opposite most Strips that will run on 12V), and that allows you to make a circuit of up to 10 meters in series or 20 meters in parallel. Given that this product runs on 24V, you cannot use a 12V power supply for this Strip . Furthermore, you will notice that this Strip is 12mm wide,which is wider than the Standard 10mm 5050 Strip. As well, given that this Strip offers 4 colors,it features 5 connectors unlike the Standard RGB Strip that normally features 4 connectors. This being said, solderless connectors are yet to be made available for this product. Should you require to cut and reconnect your RGB+White Strip, it can be cut every 6 LED (10cm)and we suggest soldering wires directly on your Strip to advantage of our customization services by calling us to place your order. Minimum fees of 15.95$ + taxes are applicable for each extension installed.

Package Includes:
1-5 meter cUL listed 300 LEDs 5050 RGB+W
iP20 LED Strip with 3M adhesive
For indoor use only
5M roll, 60LED/m. 300 LED total
Can be cut: Every 6 LED (10 cm)
Strip width: 12mm
Power consumption: 14W/m at 24V on Multi Zone Controller
                          20W/m at 24V on Advanced Multi Channel Controller
Required Power: 17W/m at 24V on Multi Zone Controller
                      25W/m at 24V on Advanced Multi Channel Controller
LED Type: 5050 SMD
Luminus flux: 720-760 lm/m
Dimmable: yes through remote control

Use of Adhesive Tape
If you're planning on installing your LED strip sideways or upside down, we strongly suggest using extra adhesive such as the Double Sided 3M 9495LE Tape for LED Strips. For porous surfaces, outdoor usage, wet and marine environments or usage with IP 68 strips, we suggest using the Double Sided 3M Acrylic Tape for LED Strips.

WARNING: Do not use the Double Sided 3M Acrylic Tape on 3014 LED Strips or for more than 4 consecutive hours at full intensity (or commercially used) 5050 Led Strips, as there could be a risk of damage to the LED strip.


PDF IconFiche-Technique-Ruban-24V-5050-RGB-W.pdf