120V Connectors and Accessories for Single Color LED Strip - 39 LEDs/m
STRPACC
Payment options
Our advantages
Find similar
120V Connectors and Accessories for Single Color LED Strip - 39 LEDs/m
PLEASE NOTE THAT THESE ACCESSORIES ARE ONLY COMPATIbBLE WITH THE 25M 39 LEDs/m 120V LED STRIP. THESE ACCESSORIES WILL NOT WORK WITH THE 25M AND 50M 118 LEDs/m 120V LED STRIP.
Â
LED Montreal offers a variety of accessories and connectors to help you customize your 120V LED Strip project.
Â
The Strip-to-Strip Two Pin Connector permits you to join two 25m LED Strips together, so that you may reach a length of up to 50m. Cut the end of the 120V LED Strip in order to expose the Strip’s connections, and slide the heat shrink tube in place on one end of the 120V LED Strip, and add the Strip-to-Strip Two Pin Connector to your 120V LED Strip, and join together.Â
Â
Warning: you will notice that the connector is not perfectly aligned with the center of the LED Strip. This is intentionally conceived so that you respect the LED Strip’s polarity. Join the other end of the LED Strip assuring the polarity is respected, and cover your connection with a shrink tube. Heat the Shrink Tube so that it completely seals your connection.Â
Â
Although double sided 3M tape may be sufficient to fasten your 120V LED Strip for most projects, the screw-attached Clips are recommended for installation in areas that are windy, atypical or to solidify installations where 3M double-sided tape is used. Offered in packs of 20, these clips are tailors made for the 120V LED Strip. Â
Â
To customize your project and adapt it to your desired measurements, you can cut your 120V LED Strip every 90cm . It is important to safeguard the endings of the LED Strip from the 120V current. The End Caps will permit you to securely shelter your Strip’s end with an aesthetic finishing. We recommend fixing the End Cap with silicon or PVC glue.
Â
The 120V LED Strip Corner Connector as its name suggests, permits you to achieve perfect right angles for your application. The installation concept is exactly the same as with the Strip-to-Strip Two Pin Connectors. Note that two Strip-to-Strip Two Pin Connectors are included with the purchase of each Corner Connector. Â The Shrink Tube is not included.
Â
The 120V LED Strip Shrink Tube is solid and waterproof. The glue-coated interior which hardens once cooled, provides an incomparable adherence and waterproofing. Install the Shrink Tube on the connection, then heat the Shrink Tube using a heat gun. The Shrink Tube will adjust to the Strip’s diameter within seconds.Â
Â
The AC/DC Electrical Extension for your 120V LED Strip is very useful should you wish to cut your 25 meter 120V LED Strip, and use the remaining part for another application. The AC/DC Electrical Extension is available is two lengths, either 60 cm (2’ ft) or 180 cm (6’ ft).  It has an included 120V AC/DC converter which measures 5.5cm x 3cm, therefore you cannot substitute the 120V LED Strip AC/DC Electrical Extension by a standard extension. The AC/DC Electrical Extension must be installed at the cut point of your 120V LED Strip using the included Polarized Two Pin Connector which has two polarized sides: the rounded side connects to the AC/DC Electrical Extension and the side with the long and pointed pins connects to your 120V LED Strip.Â
Â
As with all high voltage connections, we recommend adding Shrink Tube to secure and seal all joints. Â
Â
The accessories can be found in the drop-down menu.
Â
1. Strip-to-Strip Two Pin ConnectorÂ
2. Clips (Pack of 20)
3. End Cap
4. Corner Connector
5. Shrink TubeÂ
6a. 2 Feet AC/DC Extension
6b. 6 Feet AC/DC Extension
