24V 10m iP65+ RGB 5050 High Output LED Strip - 30 LEDs/m (Strip Only)

24V 10m iP65+ RGB 5050 High Output LED Strip - 30 LEDs/m (Strip Only)

LED Montreal offers you a simple and affordable way to color up your environment with the 24V DC 10m iP65+ RGB 5050 LED Strip. Ideal for usage in your kitchen or bedroom, it’s also everyone’s favorite to light up your home bar space. It is also fantastic to get the interior of your boat or RV ready for your next party. This Strip is not recommended for usage outside a boat or a vehicle. 

The technical stuff: RGB Stands for Red-Green-Blue. 5050 RGB Chips give a 120-degree light beam and feature each of these 3 colors of LED lights within each chip: This allows to create up to two million different colors by mixing the red, green and blue at different levels. The amount of colors that can be achieved will depend on the RGB controller that you use. Note that the RGB Chip does not create a true white. Should you want to use your Strip to both enhance your décor and get an ambient white light, we strongly suggest using our RGBW Strip that includes a white LED diode within the 5050 chips. 

RGB LED Strips have a 4-wire connection, meaning that they can only be operated through an RGB controller. The controller will allow you to dim your strip and change colors manually or through automated color change patterns. The strip cannot be dimmed through a standard wall dimmer. Forecast a power supply at 24V DC of 9W (375 mAh) per meter for your installation. As stated earlier, this strip comes in a 10m spool. You will find all the specs of the RGB LED Strip at the bottom of this page.

You can customize your LED Lighting set up as this Strip can be cut every 5 LEDS. The RGB LED Strip is flexible vertically but cannot be bent horizontally. Should you need to bypass an obstacle or turn a corner, we recommend removing the iP65+ sleeve with an x-acto knife and solder 4 strand wire onto your Strip. Soldering ensures a solid connection and minimal voltage loss. Quick connectors are available and are only recommended if you have 1 or 2 connections to make. Should you want to use a connector, use an iP20 grip and clip connector while making sure the remove both the top and bottom silicone of the Strip. Do not use connectors if the Strip is located in a wet or damp environment. 

Your RGB LED Strip is equipped with a high-quality 3M adhesive. This adhesive is intended for installation on a clean, non-glossy metallic surface. LED Strips were not designed to be installed on varnished or glossy wood surfaces. For porous surfaces, wet and marine environments we suggest using the Double Sided 3M Acrylic Tape for LED Strips.

The CDNLUX Difference: 

There are many features that make the CDNLUX LED Strips stand out from the competition. First, unlike cheaper strips that can be found on the market, the CNDLUX Strip will allow you to connect to 10 meters in series without losing brightness. 

You will also be happy to know that CDNLUX uses Authentic Epistar chips on their LED Strips. This means that you will get the best brightness for your money out of each LED Chip. As a matter of fact, Epistar Chips are 25 to 30% brighter than chips used on lower prices LED Strips that you would find on discount websites. 

CDNLUX LED Strip are cULus Listed. This means that they have been tested for electrical safety according to Canadian Standards when powered with a compliant Class 2 Power supply. It also means that they will pass the toughest building inspections both in Canada and the USA. 

CNDLUX uses iP65+ Technology on their Strips. Lower end strips are waterproofed with silicon glue that tends to crack and lose its transparency with time. Furthermore, the silicon glue is only laid on top of the strip, leaving the back of the circuit board to humidity. The CDNLUX iP65+ Technology protects your strip all around with a silicon sleeve that remains clear and flexible through time. The iP65+ coating is so efficient that a Strip equipped with this technology could be used outdoors, inside an aluminum channel in most provinces. If you are experiencing typical Canadian winters, we suggest using our iP67 Strip for outdoor applications.

With CDNLUX, you’re never on your own. Your LED Strip comes with the tech support and troubleshooting that you need to complete your project. All our representatives are based in Canada and are fully bilingual. You can reach us by email or by phone during business hours. Definitely not something you would get from an overseas seller on a discount website. 

Specifications:

Brand: CDNLUX
Model: MTL-FP10AGIWK-30ARGB
Certification: cULus for Canada and USA

Chip: Epistar 5050 RGB SMD
Chip density: 30 LEDs per meter
Can be cut: All 6 LEDs (165.5mm)
Length: 10 meters
Width: 12mm
Height: 4.25mm

Voltage: 24V DC
Power consumption: 7.2W/m
Recommended power supply: 9W/m, Class 2 power supply required
Recommended power supply for 10m: 96W, Class 2 power supply required
Available colors: RGB (Red, Green, Blue)
Lighting angle: 120°
Lifespan: 50 000 Hours

Self-adhesive: 3M
iP rating: iP65+
Suitable environment: Suitable for dry, humid environment. Indoor and protected outdoor use.
Operating temperature: 40C to -10C
Connections included: 4 pin male connector (17cm) on one end and 4 pin female connector (17cm) on the other end
Dimmable: Yes, with a low voltage controller/remote combo
Heat dissipation: Not necessary, unless used in a commercial environment