24V 10m iP67 RGB 5050 LED Strip - 30 LEDs/m (Strip Only)
24V 10m iP67 RGB 5050 LED Strip - 30 LEDs/m (Strip Only)
LED Montreal allows you to fully enjoy the benefits of the 24V Low Voltage technology with this outdoor rated continuous 10m RGB LED Strip. This CDNLUX RGB LED Strip has 30LEDs per meter and is the perfect lighting accessory for your gazebo, your outdoor terrace ou under the awning of your RV. Â
The technical stuff: RGB Stands for Red-Green-Blue. 5050 RGB Chips give a 120-degree light beam and feature each of these 3 colors of LED lights within each chip: This allows to create up to two million different colors by mixing the red, green and blue at different levels. The amount of colors that can be achieved will depend on the RGB controller that you use. Note that the RGB Chip does not create a true white. Should you want to use your Strip to both enhance your décor and get an ambient white light, we strongly suggest using our RGBW Strip that includes a white LED diode within the 5050 chips.Â
RGB LED Strips have a 4-wire connection, meaning that they can only be operated through an RGB controller. The controller will allow you to dim your strip and change colors manually or through automated color change patterns. The strip cannot be dimmed through a standard wall dimmer. You will find all the specs at the bottom of this page. Forecast a power supply at 12VDC of 9W (750mA) per meter for your installation. In other words, if you intend installing the whole spool, we recommend using a 96W power supply. As stated earlier, this strip comes in a 10m spool.Â
You can customize your LED Lighting set up as this Strip can be cut every 5 LEDS (17 cm). The RGB LED Strip is flexible vertically but cannot be bent horizontally. Should you need to bypass an obstacle or turn a corner, we recommend removing the iP67 sleeve with an x-acto knife and solder 4 strand wire onto your Strip. Soldering ensures a solid connection and minimal voltage loss. Use type 1 Silicone with our waterproofing caps to ensure a weatherproof connection. Quick connectors are available but are not recommended for outdoor usage. Â
Your RGB LED Strip is equipped with a high-quality 3M adhesive. This adhesive is intended for outdoor usage on a smooth and clean surface. We suggest using a LUX740 extrusion if you want to install your Strip on concrete or any surface where sticking a Strip is not possible.Â
Â
The CDNLUX Difference:Â
There are many features that make the CDNLUX LED Strips stand out from the competition. First, the PCB (Printed Circuit Board). We use custom PCB that ensures a consistent brightness throughout the Strip. Unlike cheaper strips that can be found on the market, the CNDLUX Strip will allow you to connect to 10 meters in series without losing brightness.Â
You will also be happy to know that CDNLUX uses Super Bright chips on their LED Strips. This means that you will get the best brightness for your money out of each LED Chip. As a matter of fact, CDNLUXChips are 25 to 30% brighter than chips used on lower prices LED Strips that you would find on discount websites.Â
CDNLUX LED Strip are cULus Listed. This means that they have been tested for electrical safety according to Canadian Standards when powered with a compliant Class 2 Power supply. It also means that they will pass the toughest building inspections both in Canada and the USA.Â
CNDLUX uses iP67 Technology on their outdoor Strips. Lower end strips are waterproofed with silicon glue that tends to crack and lose its transparency with time. Furthermore, the silicon glue is only laid on top of the strip, leaving the back of the circuit board to humidity. The CDNLUX iP67 technology protects your strip all around with a silicon sleeve that remains clear and flexible through time
With CDNLUX, you’re never on your own. Your LED Strip comes with the tech support and troubleshooting that you need to complete your project. All our representatives are based in Canada and are fully bilingual. You can reach us by email or by phone during business hours. Definitely not something you would get from an overseas seller on a discount website.Â
Specifications:
Brand: CDNLUX
Model: MTL-FP10AGIWM-30ARGB
Certification: cULus for Canada and USA
Chip: Epistar 5050 RGB SMD
Chip density:Â 30 LEDs per meter
Can be cut:Â All 6 LEDs (165.5mm)
Length: 10 meters
Width: 12mm
Height: 6mm
Voltage: 24V DC
Power consumption: 7.2W/m
Recommended power supply: 9W/m, Class 2 power supply required
Recommended power supply for 10m: 96W, Class 2 power supply required
Available colors: RGB (Red, Green, Blue)
Lighting angle: 120°
Lifespan: 50 000 Hours
Self-adhesive: 3M
iP rating: iP67
Suitable environment: Suitable for dry, humid environment. Indoor and protected outdoor use.
Operating temperature: 40C to -10C
Connections included: 4 pin male connector (17cm) on one end and 4 pin female connector (17cm) on the other end
Dimmable: Yes, with a low voltage controller/remote combo
Heat dissipation: Not necessary, unless used in a commercial environment