24V 5m iP20 3528 White LED Strip - 60 LEDs/m (Strip Only)
24V 5m iP20 3528 Single Color LED Strip - 60 LEDs/m (Strip Only)
Affordable LED lighting does not have to be low quality LED Lighting. This 24V, 3528 LED Strip will deliver great ambient lighting at an incredible price. Offered in three types of Warm White (2400K, 2700K and 3000K), Natural White (4500K), Cool White (6000K), it’s perfect to highlight crown moldings and bring a classy accent lighting to any room.
This LED Strip features 60 3528 LED Chips (3.5mm x 2.8mm) per meter over a 5m roll. These Chips give a 120-degree light beam and a light output of 400 lumens per meter. Rated at iP20, this LED UL Listed Strip offers no protection from water and dust.
Your LED Strip is equipped with a high-quality 3M adhesive. This adhesive is intended for installation on a clean, non-glossy metallic surface. LED Strips were not designed to be installed on varnished or glossy wood surfaces. For porous surfaces, wet and marine environments or usage with IP 67 strips, we suggest using the Double Sided 3M Acrylic Tape for LED Strips.
This Single Color 24V Led Strip is cULus Listed. This means that is has been tested for electrical safety according to Canadian Standards when powered with a compliant Class 2 Power supply. It also means that it will pass the toughest building inspections both in Canada and the USA.
We use custom high quality 2 OZ PCB (Printed Circuit Board) to manufacture our LED Strips to ensure a consistent brightness throughout the 24V Strip. Unlike cheaper strips that can be found on the market, this LED Strip will allow you to connect to 10 meters in series without losing brightness.
Forecast a power supply at 24VDC of 6W (250mA) per meter for your installation (30W for the complete Strip). Consult our page about power supplies to know more about the required power for your LED strip and to see our line of available power supplies.
This LED strip comes in a 5m spool and is equipped with 2-wire connection on one end and another 2-wire connection on the other end. The two-wire connection is used to connect two strips together or to hook up your Strip to a hard-wired power supply. Its low energy consumption allows you to power your strip with a 24VDC battery pack.
You can customize your LED Lighting set up as this Strip can be cut every 6 LEDS. The 5m 3528 Strip is flexible vertically but cannot be bent horizontally. Should you need to bypass an obstacle or turn a corner, we recommend that you solder 2 strand wire onto your Strip. Soldering ensures a solid connection and minimal voltage loss. Quick connectors are available and are only recommended if you have 1 or 2 connections to make. Should you want to use a connector, use an iP20 grip and clip connector while making sure the remove both the top and bottom silicone of the Strip.
The 60 LEDs 24V 3528 iP20 Single Color LED Strip is fully dimmable. You can either dim it through a remote control or a wall panel with one of our low voltage dimmers or you can dim it using an LED compatible wall dimmer when combined with one of our dimmable power supplies.
Certification: cULus E498952
Voltage available: 24VDC
Chip: Epistar 3528 SMD
60 LED chips per meter
Lighting angle: 120 degrees
Can be cut: All 6 LEDs (10cm)
Strip Width: iP20: 8mm
Power consumption: 4.8W / meter
Recommended transformer: 6W/ meter, must be powered by a Class 2 transformer
Typical luminous flux: 400 lumens/m (will slightly vary depending on Kelvin Degrees chosen)
Available colors: 2400K / 2700K / 3000K / 4500K / 6000K
Operation temperature: 40C to -10C
For indoor use only
Dimmable: Yes, through a remote/ wall panel or dimmable power supply
Heat Dissipation: Not necessary, unless used in a commercial environment
Fields of Application: Where an accent lighting is required : shelves, stairs etc.